BEFORE OPERATION GENERAL The operator presence levers are part of the interlock system. If the interlock system is not working properly, repair it bef
SAFETY PRECAUTIONS Before operating the sweeper for the first time, please review the IMPORTANT SAFETY INFORMATION beginning on page 3 and the previou
OPERATION SWEEPING Read the mid-size commercial mower owner's manual carefully. Be thoroughly familiar with the controls and proper use of the mi
OPERATION Snow Sweeping Never operate the sweeper without good visibility. Foreign objects in snow may be thrown farther than the snow itself. Use the
OPERATION SWEEPING PATTERNS These removal patterns will avoid sweeping material into unwanted places as well as eliminating a second pass. When it is
OPERATION BROOM ANGLE Broom angle can be changed from the operator’s position by using engine power to move the power unit. 1. Put the blade control
MAINTENANCE & ADJUSTMENTS THE IMPORTANCE OF MAINTENANCE Good maintenance is essential for safe, economical, and trouble-free operation. To help yo
~~~ ~ MAINTENANCE & ADJUSTMENTS MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every con
MAINTENANCE & ADJUSTMENTS MAINTENANCE SCHEDULE Use the following maintenance schedule and the maintenance schedule shown in the power unit owner&a
MAINTENANCE & ADJUSTMENTS Drive Chain and Coupling Chain Lubricate chains with GL-4 or GL-5 SAE 80w90 hypoid gear oil. Avoid getting any oil on th
PREFACE Thank you for purchasing a Honda Tested Attachment (HTA) for your Honda Mid-Size Commercial Mower . This manual covers the operation. maintena
MAINTENANCE & ADJUSTMENTS Drive Chain Slack Loosen the bolt securing the adjustment roller so the roller is free to drop down. The chain should ha
MAINTENANCE & ADJUSTMENTS BROOM CONTACT ADJUSTMENT This adjustment should be done with the rear drive axle in the 2-1/2 inch position. As the bris
MAINTENANCE & ADJUSTMENTS BROOM REPLACEMENT Whenever the broom becomes excessively tapered, worn past the service limit or sweeping is difficult,
MAINTENANCE & ADJUSTMENTS Broom Disassembly 1. Use a 1/8-inch allen wrench to loosen the set screws on the pillow block bearing opposite the 45-to
MAINTENANCE & ADJUSTMENTS Broom Assembly 1. Slide on a brush then a wafer spacer. Align brush tabs with the opening in the tri-core center. Rotat
INSTALLATION THE IMPORTANCE OF INSTALLATION Proper installation is essential to operator safety and the reliability of the machine. Any error or overs
INSTALLATION TORQUE VALUES American bolt diameter and thread size Torque Values ft-lb N•m 1/4 inch - 20 103 76 1/2 inch - 13 29.8 22 3/8 inch - 16 16.
INSTALLATION UNCRATING 1. Cut the straps and remove the crate cover. 2. Remove the loose parts bag and the shaft cover from the wooden frame, 3. Remov
INSTALLATION SWEEPER INSTALLATION If installed, remove the mower deck from the power unit. Refer to the removal procedure in the HRC7000-series shop m
SAFETY SAFETY MESSAGES Your safety and the safety of others are very important. We have provided important safety messages in this manual and on the
INSTALLATION ANGLE RELEASE CABLE INSTALLATION 1. Remove the forward throttle mounting screw. Position the cable bracket so it is parallel to the righ
INSTALLATION ANGLE RELEASE CABLE INSTALLATION (continued) 6. Secure cable to the throttle and choke cables with the cable tie. CABLE TIE W a 7. Once t
TRANSPORTING/STORAGE TRANSPORTING Move the blade control lever to OFF when transporting, or when the sweeper is not in use. Read the TRANSPORTING chap
SPECIFICATIONS Power Unit with Sweeper Attached Model * Sweeper angle set straight ahead Low range @ 2-112 or 3-112 inches Cutting height settings 763
PARTS Ref. No. Description Qty. Ref. No. Description Qty. 46 1 Plate,swing pivot I1 I 47 I Mark,Honda I1 I 48 1 Mark,contact patch 49 1 Mark,operation
PARTS 34 FS7054 FRONT SWEEPER
ADDITIONAL INFORMATION INFORMATION LABELS Record the model and serial number in the boxes below. You will need these numbers when ordering parts and w
ADDITIONAL INFORMATION OPTIONS Below is a list of available options to enhance productivity and comfort when operating your sweeper. Headlight Kit Thi
ADDITIONAL INFORMATION WARRANTY SERVICE INFORMATION Honda Power Equipment dealership personnel are trained professionals. They should be able to answe
Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: Honda Power Equipment dealership personnel are tra
SAFETY IMPORTANT SAFETY INFORMATION Most accidents with this product can be prevented if you follow all instructions in this manual and on the product
SAFETY IMPORTANT MESSAGE TO EMPLOYERS As an employer, you have special responsibilities to the people who work for you. Before you ask anyone to opera
SAFETY SAFETY LABEL LOCATIONS The labels shown here contain important safety information. Please read them carefully. These labels are considered perm
CONTROLS This chapter shows the sweeper control locations and it tells you how the sweeper controls work. It only covers controls relating to the swe
CONTROLS DESCRIPTION OF CONTROLS Sweeper Lift Crank Use the sweeper lift crank to raise and lower the broom. Turn the crank clockwise to raise the bo
CONTROLS Sweeper Angle Release T-Handle This T-handle allows the operator to release the angle lock on the sweeper. When released, the sweeper can be
Commentaires sur ces manuels